If you’re confronted with a fire, you need to be confident that your extinguisher is of the highest quality. FireSafe CO2 Extinguishers are assembled in Australia under an accredited ISO 9001 Quality Management System and are approved to AS/NZS 1841.
Carbon Dioxide is clean gas which does not leave any harmful residue making it an ideal extinguisher for use where sensitive electronic equipment is present. CO2 is non corrosive and non conductive and is also suitable for small fires involving flammable and combustible liquids.
   With a wide range of sizes and equipment types available, there is a FireSafe Extinguisher to suit practically every fire risk in the home, car, caravan or boat to the largest commercial and industrial property.

Identification: Pre 1998 - Red with centre Black Band and Post 1998 - Red with upper level Black Band.

Advantages: Clean medium therefore minimal clean up after use. Ideal for use in environment where there are computers or other sensitive electrical equipment.

Disadvantages: Only limited effectiveness on Class A and Class B Fires - refer Suitability Guide below. Not very effective for use in out-door areas as wind will dissipate the Co2 very quickly.

Servicing: Inspection and maintenance is to be performed at regular six monthly intervals as required by Australian Standard AS 1851 by an authorised or Licenced Contractor.

Chrome Plated Brass with Controllable Discharge
Light Weight Aluminium Alloy to BS 5045
Body Diameter
111 mm
140 mm
152 mm
Overall Height
540 mm
585 mm
675 mm
Projection From Wall
Approx. Full Mass **
Cylinder Test Pressure
21.9 MPa
Approx. Discharge Time
12 sec
14 sec
18 sec
Fire Rating (Still Air)
5 B:E
5 B:E
5 B:E
Discharge Assembly Type
Swivel Horn Assy. Discharge Hose & Bell Horn Assy
Paint Finish
Signal Red (R13) Epoxy Powder Coating
Metal Wall Bracket
Design & Manufacture
AS/NZS 1841.6

* Includes Swivel Horn Assembly

** Full Mass does not include swivel horn assembly or hose and horn assembly.


Suitability Guide
Class A Paper etc Class B Flam. Liquid Class C Flam Gas Class D Comb Metal Class E Electrical

Class F

Cooking Oil



FSC Carbon Dioxide - 2.0kg to 5.0kg

Contain cylinder pressure and contents of the extinguisher

a. Simple "Pull Pin/ Squeeze Lever' operation.

b. Requires less than 200 N of 'squeeze pressure' to operate.

c. Controllable discharge - operator can cease discharge and restart discharge if required.

d. Fully rechargeable

Valve Block
Contains all associated valve and discharge components

a. Chrome plated/ forged brass for maximum corrosion protection.

b. Material high strength/durable.

c. 'O' Ring seal valve - lower maintenance costs.

Handle & Lever Assy.
Enables extinguisher to be carried and operated.

a. Securely fitted to valve block for minimum wear in high vibration areas.

b. Powder coated for additional corrosion protection.

Safety Pin
Prevent accidental discharge

a. Manufactured from high strength Stainless Steel for maximum corrosion protection.

b. Attached to valve by retaining cord.

c. Removable even after direct valve lever impact of at least 4.0kg mass from height of at least 0.7 metre.

Burst Disc Safety Device
Safety vent of pressure
a. Engineered to vent extinguisher contents at a safe pressure below test pressure.

FSC2 Model

Swivel Elbow

Discharge Horn

Direct extinguishing chemical to seat of fire when discharged.

a. Stores neatly to front of extinguisher.

b. Improved flexibility in directing discharge - achieves highest fire rating for capacity.

c. No 'twist' affect compared to swivel elbows on front discharge valves.

FSD35 & 5 Models

Discharge Hose


Direct extinguishing chemical to seat of fire when discharged.

a. In built handle on discharge horn to prevent cold burn.

b. Hose enables operator to direct discharge to inaccessible positions.

c. High strength, anti corrosive hose fittings and ferules.

d. Screw locking device on valve nut - will not unscrew.

e. Locking washer on diffuser - will not unscrew.

f. Hose fittings utilize parallel threads - no wear and tear as with tapered threads.

g. Wire braid reinforced hose with internal lining and UV resistant external coating for maximum strength.

Contain the extinguishing chemical and propellant.

a. Light weight aluminum cylinder - largest capacity unit complies with WPH&S requirements.

b. Highest quality Luxfer cylinder.

c. Complaint for Australia and NZ use.

Polyester Powder

Coat Paint

Colour in compliance with AS 1841

a. UV and fade resistant -maintains AS1841 compliance for longer 'in service life' and lower maintenance costs.

b. Increased external corrosion resistance.

c. Passes 480 hour salt spray corrosion test.

FSD35 & 5 Models

Hose Band

Hose storage

a. Reduced risk of accidental damage.

b. Stores hose and nozzle neatly to the side of the cylinder.

c. Hose easily accessible for the operator.

Carbon Dioxide (CO2)
Extinguish fire

a. Food grade - 99% purity

b. Suitable and effective on small Class B fires.

c. Electrically non-conductive - tested to 110,000 volts.

d. 'Clean' gas - no messy residue after discharge.

e. Economical recharge costs.

Mounting Bracket
Secure extinguisher to an 'in service' position .

a. Suitable for fixed installation only - transport type bracket optional.

b. Will withstand up to 60kg of downward force.